TYPE: Cutter rigged cruising sloop.
HULL NUMBER: 112/003.
HULL TYPE: Round bilged with fin keel and balanced rudder.
BUILDER: Oy Nautor Ab, Finland.
NAVAL ARCHITECT: German Frers.
INTERIOR DESIGN: Dick Young.
HULL MATERIAL: Composite.
DECK & SUPERSTRUCTURE MATERIAL: GRP sandwich.
DISPLACEMENT: Approx. 127 Tons / 280.000 lbs.
GRT: 119 Tons.
BALLAST: 28 Tons.
HULL
The hull is single skin construction of glass/aramid hybrid fibre reinforced vinyl ester laminate with carbon fibre reinforcements. A high proportion of the fibres are unidirectional, giving a stiff laminate with excellent strength and fatigue properties.
Structural bulkheads are foam cored plywood laminated to hull and deck.
Stiffener flanges are unidirectional lay- ups over foam cores.
Engine beds are of GRP with steel inserts.
HULL FINISH
Topsides are finished in Flag Blue Awlgrip paint.
Boot and cove stripes finished in Oyster White Awlgrip paint.
Bottom is treated with three layers of epoxy primer and coated with two layers of black antifouling.
DECK & SUPERSTRUCTURE
DECK FINISH
Laid teak decking, 60 mm wide on deck and coach roof, cockpit coamings and soles, all glued and vacuum bagged without screws.
Composite surfaces and superstructure are finished in Awlgrip Oyster White.
KEEL & RUDDER
The ballast bulb is a lead casting with antimony attached to a steel fin.
Keel bolts are of high- tensile stainless steel.
Rudder is foam filled GRP with a tapered, lightweight, composite rudder stock supported by two self-aligning roller bearings.
An aluminium steering quadrant is bolted to the rudderstock.
STEERING SYSTEM
Twin 55” destroyer type wheels have teak trim and have 4.7 turns H.O. to H.O. Steering sheaves are bronze with stainless steel needle bearings.
Two customs Nautor made GRP steering pedestal with integral instrument with control panels port and starboard. Full engine, navigation, sailing
instruments, winch and thrusters’ controls are at both pedestals.
SUMMARY
Sleeps eight in one master and three guest cabins, all en-suite. Both aft guest cabins each have an additional pullman bed so to accommodate 2 more guests if needed.
Two crew cabins, crew mess and galley forward accommodating up to four crew.
A great deal of effort was put into the interior design of this vessel, creating a yacht of timeless classic beauty and perfectly balanced proportions.
Each room is a visual delight, an elegant blend of exotic hardwoods with the finest silks, leathers and stone available.
FOREPEAK
The foc’s’le is accessed via a deck hatch and has a watertight bulkhead aft.
The interior is painted white and has stainless rails that double as footsteps and hangers for mooring lines, sheets and halyards.
Shelves and hanging bars are installed for stowage.
CREW CABINS
There are two crew cabins forward i.e., captains’ cabin to portside with a double berth and to starboard an upper/lower berthed cabin.
Both cabins have an ensuite head with Tecma freshwater flush toilets.
CREW MESS
Aft of the crew cabins and across from the galley is the crew mess. Here there is a U-shaped sofa with seating for 4 to 5 crew.
Outboard of the sofa is a Pullman berth.
GALLEY
The galley is aft of the crew cabins and to port with the crew mess opposite to starboard. The galley is a large and U-shaped with Labrador Blue Pearl granite counter tops, Miele appliances, and custom storage cabinets.
CONTROL ROOM
A control room is located between the main saloon and galley on the port side.
This room contains the main electrical switchboards including alarm and supervision panels. There is office space with a desk and full navigation instruments.
Ample shelves for storage of manuals and files are provided
FORWARD STARBOARD GUEST CABIN
Single fixed lower berth with folding pullman berth above.
Vanity/writing desk inboard with chair.
Ensuite head finished in varnished teak and red crystal marble with gold plated taps and hardware.
Marble bathtub, washbasin, mirrors, storage lockers and Tecma WC.
MAIN SALOON
The raised salon is all on one level, designed so that a person of average height can look out the side windows while seated.
On port, there is a large U-shaped sofa with a full size with a rosewood dining table with seating for eight.
There is custom stowage for china, stemware and silverware.
Forward of the sofa are full engine controls, all of which can be hidden in a lifting cabinet.
L-shaped settee with a coffee table on starboard near the retractable 42” television.
On the aft side of the settee is a full bar with Volga Blue granite counter tops and custom glass and bottle stowage.
AFT STARBOARD GUEST CABIN
Twin berths on either side with reading lights.
Vanity desk, mirror and chair in the centerline aft.
Storage lockers beneath berths.
Folding pullman berth above inboard berth.
Hanging locker outboard aft of berth.
Hull window with curtains.
Ensuite head finished in varnished teak and forest green marble with gold plated taps and hardware.
Washbasin, shower compartment, mirrors, storage lockers and Tecma WC.
AFT PORT GUEST CABIN
Twin berths on either side with reading lights.
Vanity desk, mirror and chair in the centerline forward.
Storage lockers beneath berths.
Folding pullman berth above inboard berth.
Hanging locker outboard aft of berth.
Hull window with curtains.
Ensuite head finished in varnished teak and rose pink marble with gold plated taps and hardware.
Washbasin, shower compartment, mirrors, storage lockers and Tecma WC.
MASTER CABIN
Centerline queen sized berth, settees on port and starboard.
Writing/vanity desk with mirror forward with chair. Mirror retracts electrically to reveal 42” television.
Drawers, bookcases and storage lockers either side outboard and aft.
Ensuite head finished in Azul Macaubas marble and teak with gold plated taps and fittings. Separate shower stall, washbasin, mirrors, storage lockers and Tecma WC.
EXTERIOR COCKPIT
On the port and starboard sides are “L” shaped sofas with seating for 8 to 10 persons.
There are twin coffee tables that can be electrically raised and expanded into a dining table. On the forward end of the cockpit is a towel locker and a top loading drink fridge.
Drink holders are in the settee armrests.
GALLEY
Miele 4-burner KM 93-2 gas stove with electric oven and grill. The stove is gimbaled and has sea rails.
Miele KM 400 8 kW 2-burner Hob.
Miele Extractor Fan.
2x Miele K821i Refrigerators.
2x Miele F423i Freezers.
2x topload refrigerators, beneath crew mess floorboards.
Miele M636 Microwave.
Miele 7855 Professional Dishwasher.
U-Line Icemaker.
Miele 5065 Professional Washer.
Miele T5136 Professional Dryer.
Iceberg wine refrigerator (saloon).
HEADS/SHOWERS
Tecma Prestige 56, 24V freshwater flushing toilets in all heads.
HEATING & VENTILATION
Condaria 25 kVA/90,000 BTU air conditioning with cooling compressors and fan coils (full service 2024).
The system can be run via the generator or shore power.
Fan coils have drip pans with drains to sump.
Forced ventilation in all cabins.
Exhaust ventilators in heads and galley, and engine room.
Engine room has an air inlet with water trap.
Two fans are provided, one for inlet and one for exhaust. Power supply to the fans is interrupted on engine room fire extinguisher release. Fans are both pressure and temperature controlled.
ENTERTAINMENT
SALOON
42” Samsung flat screen TV retractable up & down.
Sonos sound system
COCKPIT
Sonos Sound System linked to Main Saloon.
GUEST CABIN PORT & STARBOARD
42” Bang & Olufsen Plasma TV and Sonos sound system.
MASTER CABIN
42” Samsung TV and Sonos sound system.
CREW QUARTERS
20” TV and Sonos sound system.
LIGHTING
All interior lighting LED, navigation lights and cockpit lighting also LED.
The engine room with full headroom is below the main saloon floor.
There is an aluminium workbench, bookshelves, parts shelves and tool storage.
ENGINE & GEARBOXES
1x MTU 6-cylinder diesel main engine, model 6R 183 TE72, rated 305 Kw/414 hp @ 1900 rpm. 14305 running hrs, April 2025.
CP Marine non-reversible reduction gear type Mekanord 270 HSK/LS, reduction ratio 2.96:1.
Drip trays under the engine and diesel generator are connected to an electric waste oil drain pump via a valve chest.
Engine and reduction gearbox are supported on flexible mounts to minimize noise and vibration.
GENERATORS
2x Northern Lights M445D 35kW (both upgraded to 42kW).
Mounted on hydro elastic sound/vibration absorbing seating, inside proprietary sound shields.
Port generator, generator end replacement and upgrade to 42kW - March 2020. Port Gen hours: 25054 (April 2025).
Stbd generator, complete replacement 42kW (12/2020) and new motor 2024. Stbd Gen hours: 4822 (April 2025) and approx. 1200 with the new motor.
Generator fuel consumption - approx. 6-8 litres per hour.
FUEL SYSTEM
The feed line to the main engine is equipped with dual Separ fuel filter/ water separators with water alarm mounted to permit uninterrupted running of engine while changing filter elements.
Each diesel generator has its own single Separ fuel filter/ water separator with alarm.
Day tank supply has Dual Racor filters to pre filter fuel prior to entering day tank.
MAINTENANCE & PERFORMANCE
Last complete service of main engine and generators 2024.
Yacht cruising speed under engine approx. 10.5 knots at 1,450 RPM.
Yacht maximum speed under engine approx. 12.5 knots at 1,900 RPM.
Fuel consumption at cruising speed approx. 55 litres per hour.
Range at cruising speed Approx. 1,200 nm.
Please note that the range at cruising speed above would only be theoretically possible when using the engine alone, in reality a generator is in use for some or all each day so the range would be reduced depending on generator use.
Fuel tanks, lines and hoses all cleaned in 2024.
PROPULSION & STEERING
Hundestedt 4-bladed variable pitch skew-back propeller with feathering position.
Propeller and shaft pulled and serviced in 2023, new seals and bearings.
Propeller shaft made of high-tensile corrosion resistant steel with flexible shaft coupling.
Drip free shaft seal.
Shaft supported by water-lubricated rubber bearing at bracket and stern tube.
The vessel is fitted with bow and stern thrusters. Both units are hydraulic, retractable Sanders 45 kW and are driven by PTO on the main engine reduction gear.
The thrusters produce approximately 600 kp thrust each.
HYDRAULIC SYSTEM
The hydraulic system is a ring system with power from four different sources:
The hydraulic system is PLC controlled and supplied by Rexroth.
The hydraulic pump operates the following systems:
Reckmann RF 90-5 hydraulic furling headstay.
Southern Spars hydraulic furling main boom.
Rondal captive winches for main halyard and main sheets.
2x Rondal captive winches for main sheet.
2x Rondal captive winches for jib sheets.
Rondal captive winch for main halyard.
Rondal captive winches for runners.
Navtec 110 boom vang.
Navtec outhaul.
Navtec twin backstay cylinders with fail safe turnbuckles.
Navtec jib halyard tensioner.
7x Lewmar hydraulic deck winches.
Sanders 45kW bow thruster.
Sanders 45kW stern thruster.
VIBRATION & NOISE CONTROL
In the design of the interior and technical systems great care has been taken to reduce vibration and noise in the accommodation and recreation areas of the vessel.
The design of the structure is undertaken with due regard to minimizing the transmission of vibration and noise to the main hull, interior, mast, etc.
Attention has been paid to the selection of ventilation fans and machinery and to their location onboard with the objective of avoiding excessive noise levels in accommodation spaces, deck recreation areas and navigating positions.
Partitions between cabins, toilets, corridors, etc. meet “comfort class” values; at anchor with one generator running the sound levels in the master-, and guest cabins are maximum 45 dB. Doors are of similar construction and have closing seals which ensure acoustic seal. All hardware is of a type designed to eliminate rattling.
DC SYSTEM
Service batteries are maintenance free gel type.
2x 24VDC banks (new 2024), one serves as DC bank, the other for the hydraulics.
Each DC bank has 12x 2V cells, Mastervolt, capacity approx. 2190 Ah at 24V – 8h.
Start batteries are maintenance free semi-traction type (new 2024) for the main engine and both generators.
Each bank has a capacity of 24 V 200 Ah/20 h.
24V 55Ah battery for supply to main engine manoeuvring system.
In an emergency situation the radio batteries can be supplied by main engine start batteries.
The DC loads can be switched in groups (inverters, hydraulic power pack and general DC consumers) to one of the service battery banks.
There is a paralleling for the engine start batteries and the service battery bank #2.
There is a paralleling button for diesel generator starter batteries and service bank.
AC SYSTEM
400V three phase five-wire AC system.
The AC system can be fed either by the diesel generators, shore power inlet or from DC/AC inverters.
All AC system is equipped with a PLC- controlled power shedding system.
ALTERNATORS
Service batteries are charged by 120-amp alternators on the main engine - one for each battery bank.
Starter battery for the main engine is charged by a 55amp alternator on the main engine.
These three alternators are equipped with external three-step voltage regulators and voltage sensing at the batteries.
Diesel generator starting battery is charged by a 24 V/35Ah alternator on each generator.
BATTERY CHARGERS/INVERTERS
4x Mastervolt 100 amps (400 VAC) battery chargers (2 replaced 2024).
2x Mastervolt 24/6000 VA inverters.
1x Mastervolt 24/3000 VA for refrigeration appliances.
1x Mastervolt 24/3000 VA for entertainment.
1x Mastervolt 24/1000 VA for 110 outlets.
SHORE POWER
AC shower power outlet is located on the transom via a hatch.
Inlet leads to an Atlas Energy System frequency converter, 30 kVA. The frequency converter accepts inlet voltages of 180 500V AC, 47 to 63Hz, 1 or 3 phase.
Shore power cable is 15 meters and is stored in a bin by a Cable Master unit.
FRESH WATER & WATER HEATING SYSTEM
Pressurized and hot and cold freshwater to all heads, the galley and deck wash outlets on fore, mid and aft deck.
A “water fixer” system with a 5 micron plated mesh filter, carbon block filter and UV chamber is installed on the cold water supply to the galley. City water connection with kinetic water softener and filter that allows shore water supply to be piped directly into the pressure water system via a pressure regulator and check valve.
WATERMAKER
Sea Recovery water maker - Coral Sea 13M3/SW/S1 (full service 2024).
Produces 544 l/h (144 US gal/h).
Equipped with remote monitor.
Dual 5-micron pre-filters and an oil/water separator.
Schenker Zen 24V water maker as back up (new 2024) - produces 100 l/h.
BILGE PUMPS
5x Electric bilge pumps:
Forepeak bilge.
Forward bilge.
Engine room bilge.
Aft bilge.
Lazarette bilge.
Each pump is equipped with a DC driven submersible pump at 140 l/min (37 US gal/ min) minimum.
2x Manual Whale Titan are installed as back up pumps, one for forepeak and forward bilge, and the other for aft and lazarette bilges.
An engine driven manual clutch pump at 250 l/min (66 gal/ min) is installed as a backup pump for the engine room bilge.
GREY & BLACK WATER
2x Black water tanks.
2x Grey water tanks.
All drained by electric Rheinstrom pumps with back-up system.
Heads discharge directly to holding tanks.
TANKAGE
FUEL
Fuel capacity approx. 6,500L in 6x stainless tanks, each with individual level indicators. Shut-off valves for each fuel tank.
Tanks are equipped with hatches of adequate size topermit inspection and cleaning, vented to deck edge.
FRESH WATER
2,500 litres in 2x stainless tanks with one filler line from deck terminating at valve chest in crew quarters.
GREY/BLACKWATER HOLDING TANKS:
Black water capacity - 655 litres in 2 tanks.
Grey water capacity - 803 litres in 2 tanks
The grey and black water pumps new 2024.
